Skip to content
PokemonCardChecker
All Articles
Grading 8 min read5 April 2026

How to Grade Your Own Pokémon Card Condition: NM, LP, MP, HP Explained with Examples

Learn to accurately grade your Pokémon cards like a professional — NM, LP, MP, HP, and DMG explained with specific criteria, common mistakes, and tools.

Why Self-Grading Matters

Whether you're buying, selling, or preparing to submit cards for professional grading, accurately assessing condition is a fundamental skill. Overestimating condition leads to disappointed buyers, disputes, and negative feedback. Underestimating condition means leaving money on the table. Getting it right is the difference between a smooth transaction and a problem.

Professional grading companies use standardised criteria — understanding them helps you predict professional grades before paying submission fees.

For the authoritative professional grading scale reference, PSA's grading standards page is the definitive source.


The Tools You Need

Before grading any card, assemble:

  • Bright LED lamp (5500–6500K daylight colour) — warm yellow light hides surface scratches
  • Magnifying loupe (10x) — Essential for inspecting corners and edges
  • Precision ruler — For centering measurements
  • Clean surface — Card sleeves or a clean microfibre cloth to rest cards on
  • Penny sleeve — Slide card in and out carefully; don't touch the card surface with fingers

Most card grading supply kits are available from Ultra PRO or general hobby suppliers.


Near Mint (NM) — The Baseline Standard

Criteria:

  • Edges: No whitening visible to the naked eye; maximum 1–2 very minor nicks
  • Corners: Sharp and fully intact; no softening or fraying
  • Surface: No scratches visible under normal lighting; holo pattern pristine
  • Centering: Within 60/40 front and back

PSA equivalent: PSA 9–10 range

Common NM mistakes:

  • Declaring a card NM because it "looks fine" without checking under magnification
  • Missing early-stage holo silvering on vintage cards (tiny grey spots on holo surface)
  • Not checking the card back — back condition is equally important

Lightly Played (LP) — Minor Visible Wear

Criteria:

  • Edges: 1–4 small edge nicks or minor whitening on one or two edges
  • Corners: Very slightly softened but not fraying or bent
  • Surface: Possibly 1–2 very minor surface scratches visible only at an angle
  • Centering: Can be slightly off but not dramatically

PSA equivalent: PSA 7–8 range

The LP test: Hold the card at arm's length under good light. If you need to look closely to spot the wear, it's LP. If you can see it immediately without squinting, it's likely MP.


Moderately Played (MP) — Noticeable Wear

Criteria:

  • Edges: Multiple edge nicks or consistent whitening along one or more edges
  • Corners: Noticeably worn or slightly fraying
  • Surface: Visible scratches or scuff marks without magnification
  • Centering: Can be significantly off-center

PSA equivalent: PSA 4–6 range


Heavily Played (HP) — Heavy Wear

Criteria:

  • Edges: Heavy whitening across multiple edges; chips or significant nicks
  • Corners: Bent, fraying, or partially splitting
  • Surface: Multiple prominent scratches, scuffs, or loss of holo texture
  • Centering: Severely off-center

PSA equivalent: PSA 2–3 range


Damaged (DMG) — Structural Issues

Any card with:

  • Creases or bends (even if pressed flat)
  • Water staining or tide marks
  • Writing, stamps, or stickers
  • Torn or split areas

PSA equivalent: PSA 1 (Poor) or Authentic


Centering: The Most Overlooked Factor

Centering is the ratio of the left border to the right border (front and back). PSA 10 requires approximately 55/45 or better front; 75/25 back.

How to measure:

  1. Place card face-up under good light
  2. Use a thin ruler to measure left border width and right border width
  3. Calculate ratio: if left = 3.2mm and right = 4.8mm, centering = 60/40 (PSA 9 territory)

Many potential PSA 10 cards fail solely on centering. Always measure before submitting. Beckett's centering guide provides additional visual examples.


Holo Silvering — The Silent Killer

Holo silvering (tiny grey spots that appear on the holo area of vintage cards) is caused by moisture exposure over time. Under a 10x loupe, it appears as small grey or silver specks scattered across the holo surface. Even a few spots can prevent a PSA 10.

It's most common on:

  • Base Set, Jungle, and Fossil holos stored in binders without sleeves
  • Cards stored in humid environments
  • Neo series cards from the early 2000s

Use PokemonCardChecker's AI grading tool for a quick digital condition pre-assessment. While AI cannot replace physical examination with a loupe, it can flag obvious condition issues before you invest time in a detailed manual assessment.

Check Your Own Cards

Use a photo-based AI assessment to organise visible condition observations and indicative prices. It is not an official grade or authentication.

Analyse a Card Free →